Fly Bottom Bracket cont

Hi

So to round off the bottom bracket post all that was left was to regrease and refit.

Didn't think i mentioned this last time, one of the balls from the old races was floating about inside the bb shell, not been looked after vary well.

These where intially bought for the lizard but that has giant races so was quite chuffed when it fit the fly.

All cleaned up using WD40, like using this at is cheap i just make sure i wash it off after use.

So pic shows a c spanner and magnetic dish, get a dish and a pick up tool really invaluale tools, also match your ball bearing orientation from your old races which usually means the balls facing outwards, tighten up your cup by hand and then add the lockring, you want your axle to spin but you don't want excess play so play about with the tightness of the cup then snug up the lock ring using your c spanner.

Another tip i picked up was to attach your crank arms loosely and spin them to see how well you have tightened and grease your bottom bracket, if it needs adjusted just pop your crank arms off a play about till your dialed in.

TNT

Fly Part One Bottom Bracket

Hi

So Fly bottom bracket overhaul

So C spanner lockring and i forget what the other part is called,fixed cup is on the other side but you dont really need to remove the fixed cup to service the bottom bracket, they can be a bitch to remove so if you don't have the right tool best leave be.

Pics

 

Lock ring removed with C Spanner

Grimy inside

So ill cover the clean and new bearings and grease going in on the next post

TNT

 

Raleigh Pioneer

Hi

So need to get the Pioneer updated and ready to ride, don't really like the name Pioneer so she is getting named Fly.

So here she is a Raleigh Pioneer Action Sport hynrid with upright bars and 700c tyres, came complete with front and rear mudguards.

So i planned for the missus to pick me up and to pop the wheels off and pop the whole lot in the boot, not so, wheels where a bitch to get off and with rear mudguard not wanting to come off there was no way it was going in.

So after a long walk home with the frame (i got picked up by a mate halfway home,not too bad) i got to have a prope look and i think she is a beauty, frame is in a lot better ncik than the Lizard, more normal sized bottom bracket than the Lizard as well.

The extra wheel i picked up with the quick release ahd to go back to the shopa nd they quite kindly swapped it for an alloy freewheel so it looks like i will be running a freewheel on the Fly and a freehuib on the lizard, the axle is near perfect in line with the frame, only needs a few mm in adjustment when i get my cone spanners.

Picked up another front 700c, the Raleigh steel one was rusted and the axle was bent so a new one was needed.

Bottom bracket overhaul next

TNT

Update -Lounging Lizard and Raleigh Pioneer

Hi

I have had to put the lizard on hold just now,currently working on  a Raleight Pioneer action sport as my main commute bike, its a lovely bikr, steel with 700c tyres, she should fly.

She needed new wheels, the front i have sourced easily but the rear came with a quick relese which i was planning on changing to solid axle but that seems to after talking to a few different mechanincs that is a PITA so beware if your going down this route, quick release won't generate enough tensionto ensure good chain posistion, you really need a nutted axle.

I had an episode of delight trying to remove the rear mudguard from this bike but that's for another day!

Apart from the wheels i putting on a single piece crankset, regreasing headset and bottom bracket, buying a lock and she should be good to go

More soon

TNT

New Handlebars

Hi

Wasn't always sure on the funky green colour of my handlebars, was in the local bike recycling centre and i found a gem in the parts bin and a bargain at £3, going to buy foam for them, was tempted to buy tape but i would have to pay somebody to tape them for me because i haven't learned to do that yet so foam for just now.

Sweet

Brake cables have come in just waiting on a cutter for them,video to follow.

TNT

The Lizard part 4 - Bottom bracket and headset in

Hi

Been away on holiday so no bike work done till i came home.

Picked up a locking nut for the headset to replace the damaged one,got some grease for the bike and picked up an adjustable wrench that fits the headset and bottom bracket and also some cutters, big note here guys bike cable is tough so your cheap cutters aint going to cut it (sorry!), i ended up paying for Draper cutters that have a god reputation and at £11 they aren't breaking the bank, i will hopfully do a video review of them as the brake system is the next big job.

 Cleaned up nicely

Crappy pic of the reinstalled bottom bracket, big tip here guys take pictures of the orientation of parts it really helps when your trying to put stuff back together.

So brakes,cranks, rear cog,stem,saddl and post still to do

Bike has internally routed rear brake cable so should be fun trying to route it through again, brake post coming next

TNT